Name: Honeywell HZ311 TrueZONE Control Panel
Brand: Honeywell

Question 1

How do I mount the HZ311 TrueZONE Panel?

Accepted Answer

Position the panel near the HVAC equipment on a wall, stud, roof truss, or cold-air return in any orientation. Separate the cover from the base and use the base as a template to drill mounting holes, then attach with appropriate screws (not included). Level the panel for appearance only.

Question 2

What accessories are available for the HZ311 TrueZONE Panel?

Accepted Answer

Recommended accessories include transformers (40 VA AT140A1042 or 75 VA AT175A1008), a Discharge Air Temperature Sensor (DATS C7735A1000), and a Slave Damper Control Relay (SDCR) for expanded functionality.

Question 3

What wire gauge should I use for the HZ311?

Accepted Answer

Use only 18-gauge solid wire (not stranded) for all connections to the HZ311 TrueZONE Panel. This ensures proper electrical performance and safety.

Question 4

What is the warranty period for the HZ311 zoning panel?

Accepted Answer

Zoning products with a date code of 0501 or later have a sixty (60) month warranty from date of installation, while zoning products with a date code of 0452 or earlier have a twenty-four (24) month warranty. The warranty covers defects due to workmanship or materials under normal use and service.

Question 5

What operating humidity range is acceptable for the HZ311?

Accepted Answer

The HZ311 TrueZONE Panel operates safely in humidity levels of 5% to 90% RH non-condensing. Ensure the installation location maintains humidity within this range for optimal performance.

Question 6

What thermostats are compatible with the HZ311?

Accepted Answer

The HZ311 supports single-stage thermostats including non-programmable models (TH5110D, TH3110D, T87N) and programmable models (TH8110U, TH6110D, TH4110D). Refer to the thermostat's specific instructions for proper installation and connection to the zone panel.

Question 7

What dampers work with the HZ311 TrueZONE Panel?

Accepted Answer

The HZ311 is compatible with spring-open/power-closed dampers (ARD Round or ZD Rectangular), power-open/power-closed dampers (MARD Round or RRD Rectangular), and static pressure regulating dampers (SPRD Round or Rectangular). Multiple dampers can be wired in parallel to the zone panel.

Question 8

How should I wire the HZ311 TrueZONE Panel?

Accepted Answer

Disconnect power before installation and wire the entire panel before applying transformer power. Run wires behind or through the wire channels on the panel's sides, attach them to a wiring anchor with a cable tie, and ensure compliance with applicable codes. Connect thermostats, dampers, DATS, equipment, and transformer according to the panel's wiring diagram.

Question 9

What are the electrical specifications for the Honeywell HZ311 TrueZONE Panel?

Accepted Answer

The HZ311 requires an 18-30 VAC, 50/60 Hz transformer of 40 VA or more, with a maximum current draw of 6.25 VA at 24 VAC. All wiring must use 18-gauge solid (not stranded) wire to ensure proper operation.

Question 10

What is the Purge Override button and how do I use it?

Accepted Answer

The Purge Override button is visible when the zone panel cover is removed. Pressing this button stops the Purge cycle, which saves time during installation or troubleshooting, and the panel will wait for the next call for Heat, Cool, or Fan. If no calls exist, the panel remains in Idle mode.

Question 11

Can I connect multiple dampers to the HZ311 panel?

Accepted Answer

Yes, multiple dampers can be wired in parallel to the zone panel. The HZ311 supports up to three zones with spring-open/power-closed dampers (ARD round or ZD rectangular) or power-open/power-closed dampers (MARD round or RRD rectangular).

Question 12

What compatible thermostats can I use with the HZ311 panel?

Accepted Answer

The HZ311 supports single-stage thermostats including non-programmable models (TH5110D, TH3110D, T87N) and programmable models (TH8110U, TH6110D, TH4110D). Install thermostats according to their individual instructions and connect them to the zone panel.

Question 13

What type of wire should I use for the HZ311 installation?

Accepted Answer

You must use 18-gauge solid wire, not stranded wire. Wires can be run behind the panel or through wire channels on the panel's sides and must be attached to a wiring anchor with a cable tie.

Question 14

What is the warranty period for the HZ311 TrueZONE panel?

Accepted Answer

Zoning products with a date code of 0501 or later are covered for sixty (60) months from date of installation. All other zoning products with a date code of 0452 or earlier are covered for twenty-four (24) months from date of installation. The warranty covers defects in workmanship or materials under normal use and service.

Question 15

Do I need to disconnect power before installing the HZ311?

Accepted Answer

Yes, you must disconnect power before beginning installation. Additionally, wire the entire panel before applying transformer power to ensure safe installation.

Question 16

What is the maximum current draw of the HZ311 zone panel?

Accepted Answer

The zone panel has a maximum current draw of 6.25 VA at 24 VAC.

Question 17

Should I disconnect power before installing the HZ311 panel?

Accepted Answer

Yes, you must disconnect power before beginning installation and wire the entire panel before applying transformer power. (Page 1 — Installation)

Question 18

What transformer models are recommended for the HZ311 panel?

Accepted Answer

Honeywell recommends the AT140A1042 (40 VA) transformer or the AT175A1008 (75 VA) transformer for use with the HZ311 panel. (Page 1 — Installation)

Question 19

What type of wire should I use to connect the HZ311 panel?

Accepted Answer

You must use 18-gauge solid wire (not stranded) for all connections to the HZ311 panel. (Page 1 — Installation)

Question 20

What is the maximum current draw for the HZ311 zone panel?

Accepted Answer

The zone panel has a maximum current draw of 6.25 VA at 24 VAC. (Page 1 — Installation)

Question 21

What is the maximum voltage input for the Honeywell HZ311 TrueZONE Panel?

Accepted Answer

The HZ311 TrueZONE Panel accepts input voltage of 18-30 VAC at 50/60 Hz from a transformer rated at 40 VA or more. (Page 1 — Installation)

Question 22

Can I mount the HZ311 panel in any orientation?

Accepted Answer

Yes, the panel can be mounted in any orientation on a wall, stud, roof truss, or cold-air return. Leveling the panel is recommended for appearance only. (Page 1 — Installation)

Question 23

Can I wire multiple dampers to the HZ311 panel?

Accepted Answer

Yes, multiple dampers can be wired in parallel to the zone panel. (Page 1 — Installation)

Question 24

How long is the warranty for zoning products with a date code of 0501 or later?

Accepted Answer

Zoning products with a date code of 0501 or later are covered by a sixty (60) month warranty from the date of installation. (Page 1 — Warranty)

Question 25

What environmental conditions is the HZ311 panel rated for?

Accepted Answer

The HZ311 TrueZONE Panel is rated for humidity levels of 5% to 90% RH non-condensing. (Page 1 — Installation)

Question 26

What voltage and transformer capacity do I need to install the HZ311 TrueZONE panel?

Accepted Answer

The HZ311 requires an 18-30 VAC, 50/60 Hz transformer with a capacity of 40 VA or more. Honeywell offers two compatible options: the 40 VA Transformer (AT140A1042) and the 75 VA Transformer (AT175A1008). All VA specifications are rated at 24 VAC.

Question 27

What does the PURGE OVERRIDE button do?

Accepted Answer

The PURGE OVERRIDE button is visible when the zone panel cover is off. Pressing it stops the Purge cycle, which saves time during installation or troubleshooting. After pressing it, the panel will wait for the next call for Heat, Cool, or Fan, or remain in Idle mode if no calls exist.

Question 28

What operating humidity conditions is the HZ311 rated for?

Accepted Answer

The HZ311 is rated for humidity conditions between 5% to 90% RH (relative humidity) non-condensing.

Question 29

Where should I mount the HZ311 panel and what preparation is needed?

Accepted Answer

Position the panel near your HVAC equipment on a wall, stud, roof truss, or cold-air return. The panel can be mounted in any orientation; level it for appearance only. Separate the cover from the base and use the base as a template to drill mounting holes, then attach with appropriate screws (not included).

Honeywell HZ311 TrueZONE Control Panel

Ask AI

Common Questions

More from Honeywell