Bosch Bosch Washing Machine (9000493008_I)
Frequently Asked Questions (10)
How do I remove the transport safety bolts before using the washer-dryer for the first time?
Unscrew all four screws using the spanner supplied, then remove all 4 transport safety bolts completely and take the mains cable out of the retainers. Insert the protective covers into the openings left after removing the bolts. Keep the transport safety bolts in a safe place, as they must be refitted if you ever need to transport the appliance again. (Page 24)
What should I do before running the washer-dryer for the very first time?
Do not load any laundry for the first run, as the washer-dryer was tested at the factory and may have residual water in the drum. Add half a measuring cup of detergent to compartment II, turn the programme selector to a 60°C programme, and press the Start button. After the programme ends, open the door and leave it open to allow the inside to dry. (Page 7)
What do the fault codes on the display mean?
The manual lists several fault codes: a door-not-closed warning requires you to close the door; a water control system activation requires you to disconnect from mains, turn off the tap, and contact after-sales service; a water-not-entering fault refers you to the 'Water is not flowing in' troubleshooting section; and a water-not-draining fault refers you to the 'Water is not drained' section. HI/End or LO/End flashing alternately indicates the maximum or minimum drying load has not been taken into account. Other fault codes are reserved for use by the after-sales service only. (Page 19)
How do I activate the childproof lock on the washer-dryer?
Press the option and set buttons at the same time to activate or deactivate the childproof lock. When the childproof lock is activated, the @ symbol lights up on the display. This prevents the washer-dryer functions you have set from being changed inadvertently. (Page 16)
How do I clean the drain pump?
First, use a screwdriver to release the lock pins, tip the kick panel and pull upwards to remove it. Take the drain hose out of the retainer, remove the plug, and release the washing water into a container, emptying it several times if needed. Once no more water runs out, replace the plug, unscrew the pump cover, clean the pump housing, remove any foreign objects, ensure the impeller turns freely, then replace and tighten the pump cover before re-securing the kick panel. (Page 18)
Show all 10 questions
What is the Fluff Clean programme and when should I run it?
The Fluff Clean programme is designed to clean the drying cycle of any fluff deposits. After 10 drying cycles, the washer-dryer displays the l (Fluff removal cycle) symbol to indicate this programme should be run, and the electronic cycle counter resets automatically afterwards. To run it, ensure the drum is completely empty, close the door, set the programme selector to Fluff Clean, and press the Start/Pause button. You can also run it at any time without prompting. (Page 12)
Why is my washer-dryer vibrating intensely during spinning?
Intense vibrations during spinning are typically caused by the washer-dryer not being correctly levelled or because the transport safety bolts have not been removed. Ensure all four appliance feet stand firmly on the ground, the machine does not wobble, and check levelness with a spirit level. If the transport safety bolts are still in place, remove them as described on page 24. (Page 20)
How do I delay the start of a washing programme?
Press the 0 (Finished in time) button repeatedly until the required number of hours is displayed; the remaining time can be set in one-hour increments up to a maximum of 24 hours. Then press the Start/Pause button, and the programme will start after a delay according to the set remaining time. The time required until the end of the programme is shown on the display. (Page 13)
What are the water pressure requirements for connecting the washer-dryer?
The water pressure in the mains supply should be between 50–900 kPa (0.5–9 bar), with at least 8 litres of water flowing out per minute when the tap is turned on. If the water pressure is higher than this range, a pressure reducing valve must be fitted. Connect the cold-water supply hose (blue union nut) to a cold water tap with a 3/4" pipe thread, and only tighten plastic screw connections by hand. (Page 26)
What laundry should NOT be washed or dried in the washer-dryer?
Do not wash laundry that has been treated with solvents, oil, wax, fat, dye, hairspray, nail varnish remover, or similar substances due to the risk of fire or explosion, and avoid laundry containing dust residues such as coal dust or flour. For drying, do not dry airtight fabrics such as rubber-coated materials, delicate materials like silk or synthetic curtains, dripping-wet laundry, or wool and fabrics containing wool. Items with the care symbol indicating 'do not wash' must also never be placed in the appliance. (Pages 3, 8)
Hi! I'm your AI assistant for the Bosch Bosch Washing Machine (9000493008_I). Ask me anything about setup, troubleshooting, maintenance, or features — I'll answer using the official manual.
Suggestions
AI answers may contain errors. Verify with the original manual for safety-critical questions.