Ask AI
— answers from the official manualAnswers from the official manual.
Common questions
Common Questions
26 totalWhat is the correct power supply voltage for the MF1643iF II in the USA versus Europe?
For USA installations, the machine requires 110-127V +/-10%, while EUR/ASIA/Oceania installations require 220-240V +/-10%. The machine should be installed near the power outlet with sufficient space around the power plug so it can be unplugged easily in an emergency. (Page 8)
How heavy is the MF1643iF II and what is the recommended way to move it?
The host machine weighs a maximum of 20 kg including toner cartridges. It is recommended to lift it with 2 or more people, and the machine must be kept level during the move. If the sales company has a standard for handling heavy loads, that standard should be followed. (Page 8)
What precautions should I take when installing the toner cartridge to protect the Photosensitive Drum?
When opening the Cartridge Cover, be sure to remove the cartridge in advance to protect the Photosensitive Drum from light. Cover the Photosensitive Drum with 5 or more sheets of paper to block light, and do not place the cartridge in a location exposed to direct sunlight such as near a window. (Page 24)
Can I install both the MiCARD Attachment Kit-B1 and the Copy Card Reader-F1 at the same time?
No, these two options cannot be used in combination with each other. The MiCARD Attachment Kit-B1 requires a Card Reader as a sales company option but is incompatible with the Copy Card Reader-F1. Similarly, the Copy Card Reader-F1 cannot be used with the MiCARD Attachment Kit or the Copy Control Interface Kit-C1. (Pages 5, 26, 43)
What is the default System Manager ID and PIN for Department ID Management on the MF1643iF II?
The default System Manager ID is 7654321 and the default PIN is also 7654321. These credentials are used when configuring Department ID Management settings after installing the Copy Card Reader. After configuring, you must turn the main power switch OFF and then ON to enable the settings. (Page 68)
How many paper feeders can be stacked on the MF1643iF II, and what is the option called?
You can stack up to 3 Paper Feeder PF-C1 units on the MF1643iF II. This paper feed option provides additional paper capacity through additional cassettes. (Pages 6, 12)
Show 20 more questions
Is it safe to throw used toner cartridges into a fire for disposal?
How many paper feeders can I stack on this machine?
What should I remove before using the USB port?
What power supply voltage is required for the Canon MF1643iF II in the USA?
How heavy is the Canon MF1643iF II and how should it be moved safely?
What is the correct procedure for turning off the Canon MF1643iF II before servicing?
How should I install the toner cartridge in the Canon MF1643iF II?
Can the Copy Card Reader-F1 be used together with the MiCARD Attachment Kit-B1?
How many paper feeders can be stacked on the Canon MF1643iF II, and what is the maximum?
What is the default System Manager ID and PIN for the Department ID Management on the Canon MF1643iF II?
How should I handle the host machine during unpacking and installation?
What voltage specifications does this printer require?
What precaution should I take if moving the machine from a cold to warm location?
How do I install a toner cartridge?
What should I do before opening the cartridge cover to protect the photosensitive drum?
Can I use the MiCARD Attachment Kit-B1 with other card reader options?
What are the safe operating temperature and humidity ranges for the Canon MF1643iF II?
How do I properly install a toner cartridge in the MF1643iF II?
What is the correct procedure for turning off the main power before servicing the MF1643iF II?
What should I do if the Canon MF1643iF II has just been moved from a cold location to a warm location?
Full Manual
94 pages
Installation
Manual
imageCLASS X MF1643iF II MF1643i IICanon
June 9, 2021 Rev. 1
Copyright © 2021 Canon Inc.
CANON imageCLASS X MF1643iF/i II Rev. 1 PRINTED IN U.S.A.
Important Notices Application This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality. Following "Trademarks" and "Copyright" are not applicable if they are not supported by laws and regulations in the country or region that this document and products are used in. Corrections This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products. When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual. Trademarks The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Canon is under license. Mopria®, the Mopria® Logo and the Mopria® Alliance logo are registered trademarks and service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited. Apple, AppleTalk, Bonjour, iPad, iPhone, iPod touch, Mac, OS X and Safari are trademarks of Apple Inc. Microsoft, Windows, Windows Vista, Windows Server, Internet Explorer, Microsoft Edge, Excel and PowerPoint are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Google Cloud Print, Google Chrome and Android are either registered trademarks or trademarks of Google Inc. OCR Technology by I.R.I.S., copyright 1987-2015, All Rights Reserved. iHQC™ compression technology by I.R.I.S., copyright 2007-2015, All Rights Reserved. PDF-iHQC™, XPS-iHQC™ technology by I.R.I.S., copyright 2007-2015, All rights Reserved. Java is a registered trademark of Oracle and/or its affiliates. Adobe is a registered trademark of Adobe Systems Incorporated. Command WorkStation, EFI, Fiery, FreeForm, Spot-On, and WebTools are trademarks of Electronics For Imaging, Inc. and/or its wholly owned subsidiaries in the U.S. and/or certain other countries. TORX® is a registered trademark of Acument Intellectual Properties, LLC in the United States. Other product names and other names in this document are generally registered trademarks or trademarks of the companies. Important Notices
Copyright The copyright of this document belongs to Canon Inc. This document may not be copied, reproduced or translated into another language, in whole or in part, without the prior consent of Canon Inc. Copyright CANON INC. 2021 Caution Use of this manual should be strictly supervised to avoid disclosure of confidential information. Symbols The frequently-performed operations are described with symbols in this procedure. 1x 1x 1x Install Screw Packaged Item Remove Tighten Loosen 1x Connect Connector Disconnect Install Harness (Common for Guides and Clamps) Remove 1x 1x Connect Power Cord Disconnect Check visually Check the sound Check
Off
CleaningOn
Push Power Unused Parts 1x 1x Important Notices
Contents Safety Precautions...............................................................................................1 About Toner.........................................................................................................................................2 Points to Note at Installation................................................................................................................2 Checking the Installation Environment....................................................................................................2 Points to Note Before Servicing..............................................................................................................2 Essential Items to Be Performed Before Installation.................................................................................2 illustrations........................................................................................................................................... 3
Revision.............................................................................................................. 89 Contents ii
Safety Precautions About Toner.......................................... 2 Points to Note at Installation................. 2
About Toner Toner is a non-toxic material composed of plastic and small amount of pigment.
Caution:
Never throw toner in flames to avoid explosion. Points to Note at Installation Checking the Installation EnvironmentCaution:
Leaving the power plug connected for a long time in an environment having a lot of dust, moisture, or oily smoke will cause a fire. (Because dust accumulated in the surrounding area will absorb moisture and cause an insulation failure)Caution:
Hazardous area such as corners, edges, springs and other sharp sections may be remaining on products. Always be aware of the presence of hazardous area to avoid injury caused by contacting and/or striking those area, by not over- concentrating on service work. Essential Items to Be Performed Before InstallationWarning:
illustrations Although pictures or illustrations used for explanationmay differ from the actual things, the procedure is the same. Safety Precautions 3
Product Lineup 1 Host Machine Options...........................5 Paper Feed Options..............................6
Host Machine Options
Telephone 6 Kit
Long cord Cool White Copy Control Interface Kit-C1 Copy Card Reader-F1 Copy Card Reader Attachment-J1 MiCARD Attachment Kit-B1 No. Product Name Condition Reference 1 MiCARD Attachment Kit-B1 Card Reader (sales company's option) is required. Using with Copy Card Reader-F1 is not available. “MiCARD Attachment Kit-B1” on page 21 2 Copy Card Reader-F1 Copy Card Reader Attachment-J1 Using with MiCARD Attachment Kit-B1 and Copy Control Interface Kit-C1 are not available. “Copy Card Reader-F1 / Copy Card Reader Attachment-J1” on page 43 3 Copy Control Interface Kit-C1 Using with Copy Card Reader-F1 is not available. “Copy Control Interface Kit-C1” on page 69 4 TELEPHONE 6 KIT Long cord Cool White Only for model with FAX function (EUR only) “Handset (Only for model with EUR/FAX function)” on page 14 License Products At the time of installation, obtain the license number. Then, enter the obtained license number from the Control Panel of the machine. applicable functions are enabled. There is no physically required installation. No. Product Name Condition 1 PS Printer Kit-CB12 Barcode Printing Kit-E1
Paper Feed Options Paper Feeder PF-C1 No. Product Name Condition Reference 1 Paper Feeder PF-C1 A paper feeder with up to 3 cassettes can be installed. “Paper Feeder” on page 11
Host Machine 2 Checking before Installation..................8 Installation Procedure........................... 9
Checking before Installation Checking the Power Supply
• Usa: 110-127V +/-10%
Installation Procedure Unpacking
Caution:
Do not remove the sticker on the USB port until you use it.
Loading Paper
Checking the Contents Only for model with FAX function 1x Latin America (220-240V), AUS, SPL only 1x Latin America (220-240V),
Eur, Aus, Spl
Only for model with FAX function 3x 1x 1 2 *1: Used to connect the host machine and PC. *2: Used for Handset (option) installation. < Others >Note:
If no Option is installed, proceed with “ Installing the Toner Cartridge (In case no Toner Cartridge is installed)” on page 16. ■ Paper Feeder ● Included Items 1x 1x
● Installation Procedure
Note:
You can stack up to 3 paper feeders.
Note:
Note:
Note:
Installing the Included Items
Telephone line jack Telephone Handset (Optional) Turning ON the Main Power Switch
Note:
Refer to the "Setup Guide" for the following detailed procedures. Operation when using uniFLOW Online When using uniFLOW Online*, follow the setup procedures on the uniFLOW* Online First Steps Guide (http://www.nt-ware.com/ uFO_FS).
Host Machine Options 3 MiCARD Attachment Kit-B1................ 21 Copy Card Reader-F1 / Copy Card Reader Attachment-J1.....................43 Copy Control Interface Kit-C1............. 69
MiCARD Attachment Kit-B1 Points to Note at Installation Prepare a Card Reader (sales company's option) in advance. Regardless of the shape of the Card Reader, the installation method is the same. Use the shorter cable of the Card Reader. The following options cannot be used in combination with this equipment.
Installation Procedure ■ Installing the CR Plate
Note:
[A]
[A]
Caution:
Note:
The removed parts will be used in step 13.
Note:
8-3. 8-4. Proceed to step 10.
Caution:
When turning the host machine on its side, be careful not to let the ADF open.
9-2.
9-3.
Note:
11-2.
Caution:
Shift the host machine back to the center of the working table to prevent it from falling down. 11-3. Proceed to step 13.
12-2.
Caution:
When standing the host machine, be careful not to let the ADF open.
Note:
Note:
[A]
[A]
Note:
Copy Card Reader-F1 / Copy Card Reader Attachment-J1 Points to Note at Installation The Copy Card Reader Attachment is required for the installation of the equipment. The following options cannot be used in combination with this equipment.
Installation Outline Drawing Installation Procedure ■ Installing the Connector Unit/CR Plate
Note:
[A]
[A]
Caution:
Note:
The removed parts will be used in step 15.
Note:
8-3.
8-4.
Caution:
Shift the host machine back to the center of the working table to prevent it from falling down. 8-5. Proceed to step 10.
Caution:
When turning the host machine on its side, be careful not to let the ADF open.
9-2.
9-3.
Note:
Caution:
When cutting off the part, be sure not to make burrs.
Note:
Note:
Shift the host machine so that its legs [A] are on the edge [B] of the working table.[A]
[B]
[B]
[B]
[A]
13-2. 13-3.
Caution:
Shift the host machine back to the center of the working table to prevent it from falling down.
13-4. Proceed to step 15.
14-2.
Caution:
When standing the host machine, be careful not to let the ADF open.
Note:
Note:
[A]
[A]
Caution:
[A]
Caution:
[A]
Note:
[A]
Note:
Setting after Installation Configure the card management information settings in service mode.
Copier > Function > Install > Card-Num
Note:
System Manager Login
Copy Control Interface Kit-C1 Points to Note at Installation The following options cannot be used in combination with this equipment.
Installation Procedure
Note:
[A]
[A]
Caution:
Note:
The removed parts will be used in step 15.
Note:
8-3.
8-4.
Caution:
Shift the host machine back to the center of the working table to prevent it from falling down. 8-5. Proceed to step 10.
Caution:
When turning the host machine on its side, be careful not to let the ADF open.
9-2.
9-3.
Note:
Caution:
Note:
Note:
Shift the host machine so that its legs [A] are on the edge [B] of the working table.[A]
[B]
[B]
[B]
[A]
13-2. 13-3.
Caution:
Shift the host machine back to the center of the working table to prevent it from falling down.
13-4. Proceed to step 15.
14-2.
Caution:
When standing the host machine, be careful not to let the ADF open.
Note:
Note:
[A]
[A]
Revision Rev . Chapter Category Product Name Reference Remarks 1.0