Ask AI
— answers from the official manualAnswers from the official manual.
Common questions
Common Questions
20 totalHow do I set up and do the initial cleansing brew on my K Select K80?
Remove packing tape, plug into a grounded outlet, and place a large mug (355 ml/12 oz minimum) on the drip tray. Remove the water reservoir lid, rinse the reservoir with fresh water, fill to the MAX fill line, and replace it. Press the power button and wait about 3 minutes for the water to heat, then lift and lower the handle without a K-Cup pod and press the small cup (117 ml/6 oz) button to run a cleansing brew, pouring the hot water into the sink. (Page 2)
What is the Auto Off feature and how do I disable it?
Auto Off automatically turns your coffee maker off 2 hours after the last brew for energy savings. To disable it, power the coffee maker off while plugged in, then press and hold the Strong and 296 ml/10 oz Large Mug buttons for 3 seconds until the green Auto Off light turns off, then power the coffee maker back on. To re-enable the feature, repeat the same steps. (Page 2)
How do I enable High Altitude Brewing Mode?
High Altitude Brewing Mode should be enabled if you are brewing at altitudes above 1,500 m/5,000 ft. To enable it, power the coffee maker off while it is plugged in, then press and hold the Strong and 237 ml/8 oz Small Mug buttons for 3 seconds — both lights will blink 3 times to confirm activation. You should also manually push the K-Cup pod down in the holder until the bottom is punctured by the exit needle before brewing. (Page 2)
How do I clean the entrance and exit needles to fix grounds in my coffee?
To clean the exit needle, remove the K-Cup pod holder assembly, detach the funnel, and insert a straightened paper clip into the exit needle to loosen and push out the clog. To clean the entrance needle, lift the handle and carefully insert a straightened paper clip into both holes on the underside of the lid, gently moving it to loosen coffee grounds, then lower the handle and run two water-only brew cycles without a K-Cup pod. (Page 3)
How often should I descale my K Select K80, and how long does it take?
You should descale your coffee maker every 3-6 months, though calcium deposits may build up faster and require more frequent descaling. The full descaling procedure takes approximately 45 minutes to complete. You will need a large ceramic mug, fresh water, and Keurig Descaling Solution — do not use a paper cup. (Page 4)
What are the steps to descale the K Select K80?
First, empty the water reservoir, pour the entire bottle of Keurig Descaling Solution into the reservoir, then refill the empty bottle with water and add that too. Run rinsing brews using the largest brew size until the add water light illuminates, then let the coffee maker sit on for at least 30 minutes before discarding the remaining solution. Finally, fill the reservoir with fresh water and run at least 12 rinsing brews using the largest brew size, refilling the reservoir as needed. (Page 4)
Show 14 more questions
My coffee maker is only brewing a partial cup — what should I do?
Why won't my coffee maker turn on or keeps shutting off?
How do I properly store the K Select K80 when not in use?
How do I clean the entrance and exit needles in my Keurig K-Select K80?
What size mug should I use for my Keurig K-Select for an average cup?
How often should I descale my Keurig K-Select coffee maker?
How do I power my Keurig K-Select back on if it shuts off unexpectedly?
What does the warranty cover and how do I get warranty service?
What should I do if my Keurig K-Select has stopped brewing properly?
How do I set up auto-off for my Keurig K-Select?
How do I clean the exterior of my Keurig K-Select coffee maker?
How do I clean the drip tray of my Keurig K-Select coffee maker?
How can I ensure strong coffee from my Keurig K-Select?
What do I need to do if I'm using a high-altitude brewing setup with my Keurig K-Select?
Full Manual
6 pages
K-SELECT™
Use & Care Guide
Get the most from your new Keurig® brewer
Before You Brew
1 2
Plug & Place Rinse & Fill
Remove packing tape from brewer and plug into a grounded outlet.
Remove the water reservoir lid, then lift the reservoir straight up to remove it.
If you have a Keurig® Water Filter, install it now. Refer to your Water Filter Starter Kit for instructions.
Place a large mug (12oz. minimum) on the drip tray plate.
Rinse reservoir with fresh water and fill to the MAX fill line.
Replace water reservoir, making sure the lock tab engages with the brewer. Replace lid. NOTE: Do not use distilled water.
3 4
Power On Lift & Lower
Lift and lower the handle. Do not
Press power button — the green power light and Auto Off light will illuminate.
insert a K-Cup® pod. The four brew buttons and the Strong button will blink.
Auto Off
Descale
Strong
The brewer will automatically begin heating the water. This will take about 3 minutes. Once the heating sound stops, the brewer is ready.
Add Water
Press the small cup button to start a cleansing brew. Pour the hot water into the sink.
The one-time setup process is now complete and you are ready to brew!
Brew Your First Cup
5
Place Mug
Place a mug on the drip tray plate. If using a travel mug, remove the drip tray and place the mug on the drip tray base. NOTE: Between brew cycles, the brewer may take about a minute to reheat.
7
Brew & Enjoy
Select your brew size – for bolder coffee, press the Strong button before selecting your brew size. The brew size and Strong button, if selected, will remain illuminated while brewing – about 1 minute.
Travel Mug 12oz.
Strong
Large Mug 10oz.
Travel Mug 12oz.
The brewer will be ready to brew another cup in about a minute. NOTE: After 60 seconds, the brew buttons will be disabled. To re-activate, lift and lower the handle completely. CAUTION: While brewing, there is extremely hot water in the K-Cup® pod holder. To avoid injury, do not lift the handle during the brewing process.
Small Mug 8oz.
Large Mug 10oz.
Small Cup 6oz.
6
Lift & Insert
Lift the handle and place a K-Cup® pod in the K-Cup® pod holder. Lower the handle completely to close the lid.
Do not remove the foil lid on the K-Cup® pod.
Brewer Features Strong Brew kicks up your coffee’s strength and intensity. For bolder coffee, press the Strong button before selecting your brew size.
Smart Start heats then brews in one simple process. No need to wait for the brewer to heat before selecting brew size. Power on your brewer, place mug, insert a K-Cup® pod, and lower the handle. Then, select your brew size. The brewer will heat, then automatically begin brewing. Auto Off automatically turns your brewer off 2 hours after the last brew for energy savings. To disable the Auto Off feature:
To enable the Auto Off feature, repeat steps 1-3. The green Auto Off light will illuminate. High Altitude Brewing: To ensure your brewer works properly at higher altitudes (5,000 feet) please follow these brewing instructions and enable the High Altitude Brewing Mode on your brewer.
Brewing Instructions - While holding the brewer handle up, push down slowly on the K-Cup® pod in the pod holder until the bottom of the K-Cup® pod is punctured by the exit needle.
To enable High Altitude Brewing Mode:
To disable High Altitude Brewing Mode:
##### Caring for your Brewer
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
####### Brewer Exterior
Keep your Keurig® brewer looking its best by cleaning the exterior from time to time. Just clean with a damp, soapy, lint-free, non-abrasive cloth. Never immerse the brewer in water or other liquids.
####### Drip Tray
The drip tray can hold up to 8 ounces of overflow and should be emptied and cleaned occasionally. To remove, slide it toward you, keeping it level to avoid spilling. Clean in dishwasher (top rack only) or rinse and clean with a damp, soapy, lint-free, non-abrasive cloth.
####### Water Reservoir & Reservoir Lid
The water reservoir lid and water reservoir should be cleaned periodically. Clean in a dishwasher (top rack only) or hand wash. To hand wash, use a damp, soapy, nonabrasive cloth. Rinse the reservoir thoroughly after cleaning. This will ensure that no cleaning solutions remain in the area as they may contaminate the water supply. After
rinsing, fill the reservoir with clean water and return it to the brewer. Do not dry the inside of the water reservoir with a cloth as lint may remain. If needed, repeat above procedures. NOTE: If you are using a water filter inside the water reservoir, remove it before cleaning.
####### K-Cup® Pod Holder
To remove the K-Cup® pod holder from the brewer, lift the handle and grasp the top of the K-Cup® pod holder with one hand while pushing up on the bottom of the K-Cup® pod holder from underneath with the other until it releases. After cleaning, align the K-Cup® pod holder with the opening using the two front ribs as a guide and snap into place from the top.
CAUTION: There are sharp needles that puncture the K-Cup® pod above the K-Cup® pod holder and in the bottom of the K-Cup® pod holder. To avoid risk of injury, do not put your fingers in the K-Cup® pod holder.
####### Funnel
The funnel can be removed from the K-Cup® pod holder by pulling on it until it pops off. To replace it, just snap it back onto the K-Cup® pod holder.
| | | |---|---| | | |
####### Exit Needle
Remove the pod holder assembly and detach the funnel. Locate the exit needle on the inside bottom of the K-Cup® pod holder. Insert a straightened paper clip into the exit needle to loosen the clog and push it out.
####### Entrance Needle
Lift the brewer handle and locate the entrance needle on the underside of the lid. To clean both holes in the needle, hold the brewer handle in the upward position and with your other hand, carefully insert a straightened paper clip into both holes. Gently move it around to loosen any coffee grounds. Lower the handle completely and run two water-only brew cycles. Do not insert a K-Cup® pod. TIP: Refer to support.Keurig.com for video instructions on cleaning the entrance/exit needles.
##### Descaling your Brewer
You should descale your brewer every 3-6 months. Properly follow the descaling procedure.
Depending on the mineral content of your water, calcium deposits or scale may build up in your brewer. Scale is nontoxic but if left unattended can hinder brewer performance. Regularly descaling your brewer every 3-6 months helps maintain the heating element, and other internal parts that come in contact with water. Calcium deposits may build up faster, making it necessary to descale more often.
####### Descaling Procedure
Before you begin, you will need a large ceramic mug, fresh water, Keurig® Descaling Solution, and access to a sink. Do not use a paper cup. Ensure that there is no beverage pod in the K-Cup® pod holder. Please allow approximately 45 minutes for the descaling procedure.
Empty the water from the water reservoir. If using a Keurig® Water Filter, remove and set aside.
STEP 1: Descaling Solution Rinse Press the power button to power the brewer off. Pour the entire bottle of Keurig® Descaling Solution into an emptied water reservoir. Then fill the empty bottle with water and pour into the water reservoir. Press the power button to turn the brewer back on. Place a large mug on the drip tray and run a rinsing brew by lifting and lowering the handle and selecting the largest brew size.
####### STEP 2: Descaling Rinse & Repeat
Repeat the rinsing brew process until the add water light is illuminated. Do not use a K-Cup® pod. Let brewer stand for at least 30 minutes while still on.
After 30 minutes, discard any residual solution from the water reservoir and rinse thoroughly.
####### STEP 3: Fresh Water Rinse
Fill the water reservoir with fresh water to and not beyond the MAX fill line.
Place a large mug on the drip tray plate and run a rinsing brew using the largest brew size. Do not use a K-Cup® pod. Pour the contents of the mug into the sink.
Repeat brew process until you have completed at least 12 rinsing brews using the largest brew size. You may need to refill the water reservoir at least one time during this process. NOTE: The cleaning action of Keurig® Descaling Solution may result in a “foam” dispensed from the brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added. If this occurs, you may see only a small or no output dispensed, followed by the sound of air blowing out. If this occurs:
##### Troubleshooting
####### Grounds in Your Coffee
Grounds may have gathered in the exit or entrance needles and can be cleaned using a straightened paper clip or similar tool.
####### Brewer Will Not Brew
####### Brewing a Partial Cup
####### Brewer Does Not Have Power or Shuts Off
####### Helpful Hints
Water quality varies greatly. If you notice an undesirable taste in your beverage (such as chlorine or mineral tastes), we recommend using bottled or filtered water. Do not use distilled water. You can also install a Keurig® Water Filter to help remove water impurities and improve beverage taste.
####### Service
Beyond these recommended cleaning and maintenance procedures, this brewer is not user serviceable. For service, please refer to the Warranty section of this guide.
####### Storage
Empty the water reservoir before storing or transporting and take care to ensure that you store your brewer in a safe and frost free environment. Please be sure to store your brewer in its upright position to avoid water leakage from the inner tank. If you store the brewer in a cold environment, you run the risk of water freezing inside the brewer and causing damage. When you prepare to use it after storage, we recommend rinsing the water reservoir with fresh water and running three rinsing brews without a K-Cup® pod.
If you plan to move your brewer to a different location, turn the brewer off, unplug it, and empty the water reservoir. If your brewer has been in an environment below freezing, please be sure to let it warm to room temperature for at least 2 hours before using.
##### Click or Call!
####### Have Questions?
We’re here to help. Visit support.Keurig.com for step-by-step videos on cleaning, descaling, and more.
Still Need Help? Give us a call at 1-866-901-BREW (2739)
##### Warranty
######## LIMITED ONE YEAR WARRANTY
Keurig Green Mountain, Inc. (Keurig) warrants that your brewer will be free of defects in materials or workmanship under normal home use for one year from the date of purchase. It is recommended that you register your brewer on Keurig.com/new so that your purchase information will be stored in our system. Keurig will, at its option, repair or replace a defective brewer without charge upon its receipt of proof of the date of purchase. If a replacement brewer is necessary to service this warranty, the replacement brewer may be new or reconditioned. If a replacement brewer is sent, a new limited one year warranty will be applied to the replacement brewer.
This warranty only applies to brewers operated in the United States and Canada. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state and, in the case of Canada, from province to province.
Only the use of Keurig® K-Cup® brand pods and accessories will guarantee the proper functioning and lifetime of your Keurig® brewer. Any damage to or malfunction of your brewer resulting from the use of non-Keurig® pods and accessories may not be covered by this warranty or may result in a service fee if the damage or malfunction is determined to be caused by such use.
######## WHAT IS NOT COVERED BY THE LIMITED WARRANTY?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you depending on the state or province of purchase.
Nor does this warranty cover damages caused by use of non-Keurig® pods or accessories, services performed by anyone other than Keurig or its authorized service providers, use of parts other than genuine Keurig® parts, or external causes such as abuse, misuse, inappropriate power supply, or acts of God.
######## OTHER LIMITATIONS
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR K-SELECT™ BREWER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you depending on the state or the province of purchase.
######## HOW DO YOU OBTAIN WARRANTY SERVICE?
Keurig® brewers are high-quality appliances and, with proper care, are intended to provide years of satisfying performance. However, should the need arise for warranty servicing, simply call Keurig Customer Service at our toll free phone number 1.866.901.BREW
(2739). Please do not return your brewer for servicing without first speaking to Keurig Customer Service to obtain a Return Materials Authorization (RMA) number. Keurig® brewers returned without a RMA number will be returned to the sender without servicing.
##### K-SELECT
##### BREWER
™
A
E
G
MAX
###### F
For replacement parts, please visit www.Keurig.com
Fully experience the benefits that come with your new Keurig® brewer at
KEURIG.COM/NEW
|✓| |---|
#### REGISTER DISCOVER
your new Keurig® brewer to activate your warranty and receive a special savings offer
your favorite coffees with our customized taste quiz and get personalized recommendations